* Buy Together & Subscriptions orders are not eligible for Cashback
Free shipping over $25
Free Shipping on All Orders Over $25.
You may request a return within 30 days from the date the product is shipped.
All returns may be tentative on brand approval.
🍓🍓How to Make a Better Strawberry Pallet Planter🍓🍓
Home & Garden
Make a Better Strawberry Planter out of a Wooden Pallet
The dimensions of my pallet planters are: 47" wide, 16" across, and 19" in height
You will need the following materials:
- A suitable pallet as described above
- A Hand Saw or Jigsaw
- Electric Drill or Hammer
- 4 cm (1-5/8") Screws and 8cm (3") Screws
- OR 4 cm (1-5/8") Nails and 8cm (3") nails This assortment should do
- Heavy duty Splitting Wedge and Iron Mallet
- Non-toxic paint and paintbrush
Step 1: Cut the pallet into three equal pieces
The easiest way to do this is to cut lay the pallet so that the long planks are in parallel with your own position. If your pallet has nine planks, like mine did, then count over three planks and then saw the wood between the third and fourth planks. Saw right in the middle, to keep things easy and to ensure that all of your proportions remain correct. Continue another three planks and cut again. Remember that you'll have to saw in the exact places on both the front and back of the pallet.
Step 2: Trim and remove excess wood pieces
You'll have three pieces of pallet now, all of the same height and width. Two of the pallets will be formed from the top and bottom and will have chunky blocks securely fixed to them between one of three planks on the front side and the single one left on on the other. You'll want to trim off the excess wood jutting up from each one of these wooden blocks. Please refer to images for step one and two. Though I chose not to do it in this project, you could also remove that single plank on the back side.
Step 3: Fix the two end pieces to the middle part of the pallet. Screw in from the other side of the middle (bottom) piece.
The two end pieces will be the sides of your planter and the middle piece is the bottom. Though the image shows the structure right way up, it's actually easier to flip it over in order to fix the bottom piece to the sides. You'll want to screw or nail the bottom piece into the wooden blocks still attached to the side pieces.
Step 4: You should have three to four of these pieces that were removed from the centre piece of the pallet. Separate them into individual blocks and planks.
This is easier said than done if you don't have the right tools. Since pallet wood that has been heat treated can be brittle if you try to pull the plank off with the tongs of a hammer. If you have a heavy Splitting Wedge then I recommend that you use it to separate the block and the plank and sever the nails in two. If you're planning on doing any more pallet projects you could really save yourself a lot of tears and invest in one along.
Step 5: Use planks to create the sides and the blocks for feet
If you've followed the directions in step 1 and sawed in the middle between the long planks, then the little planks leftover from step four should all be approximately the same length. They will also be the same width you need to create the shorter sides of your planter. If your original pallet was the same size as mine then you'll have four of these planks to make up two pieces for each side.
Well almost :) Turn your planter right way up and have a look at it. Does it feel sturdy? Are the feet wobbly? Are there extra bits of wood sticking up that you could trim back? Once you feel the planter is complete then either plant it up as is or use a non-toxic outdoor wood paint to paint the exterior. Being wood, this piece will eventually rot down but some tlc now can help extend its life.
Plant it up
Soil and compost will erode through any unprotected opening in the sides or bottom of the planter. Putting down your choice of barrier materials will help keep that soil where it's supposed to be. I chose to line the bottom of my planter with scraps of wire then a layer of Landscaping Fabric that will let water out but keep matter in. Since I placed my planter against a hedge I also chose to roll the black material up the back since I won't be planting any strawberries on that side. On top of the fabric and running up the sides I used straw as an organic erosion barrier.
Here's a before and after shot of how my planter looked on the day of construction and how it looks today. In two months the plants have grown enormously and I'm picking ripe berries every day. I've planted my container with two types of strawberry and the most prolific are the ever-bearing variety that should produce fruit for most of the summer.