* Buy Together & Subscriptions orders are not eligible for Cashback
Free shipping over $25
Free Shipping on All Orders Over $25.
You may request a return within 30 days from the date the product is shipped.
All returns may be tentative on brand approval.
How To Make A Wine Bottle Bird Feeder :)
DIY & Crafts
(1) 8 foot 1 x 2 pine furring strip (my local price $1.18)
(1) 8 foot 1 x 4 pine furring strip ($2.08)
(1) 3/16 x 2 x 2 piece luan plywood ($3.48)
Hose clamp (such as this)
wine bottle (11 inches long)
brad nailer or hammer and nails
2 – 1×2 @ 11″ These should be cut at 45* on one end, with a 5/16th” wide channel that is 1/4″ from the bottom of the side and 1/4 deep. They also need the same channel running vertically 1/4″ from the back.
2) 2 – 1×2 @ 3 5/8″ These pieces will need a channel that is 5/16th” wide channel that is 1/4″ from the back and 1/4″ deep.
3) 1 – 1×2 @ 4 5/8″ This will also be needing the same channel that is 5/16th” wide and 1/4 ” from the back and 1/4″ deep as well as a channel on the top using the same measurements.
1 – 1×2 @ 6″ Again, this piece will need a channel that is 5/16th” wide, 1/4″ from the back and 1/4″ deep.
5) 2 – 1×4 @ 6″ These boards form the roof and need to have opposing (parallel) 45* angles. They also need to have the same channel as above: 5/16th” wide by 1/4″ deep, 1/4″ from the back.
6) 1 – plywood @ 5×5″
7) 1 – plywood @ 5×12 1/2″ Angled at 45* down to 10″ at sides
After cutting all of the pieces to size, cut small channels into each piece (as noted above in the cut list) using a table saw. The channels will help the bird feeder fit together snugly and securely as well as look nicer. The deeper the channel is, the more movement before assembly. The tighter the channel, the more stable it will be. After all pieces and channels are cut, you should end up with something similar to the above picture. Make sure to dry fit pieces as you work to ensure that they fit together nicely. It is much easier to correct small issues at this point than when you are
are trying to glue and nail.
Here are some more close up shots of what the pieces should look like before assembly:
Fit the hose clamp around the wine bottle to measure for size. Using a small drill bit, or a utility knife make openings just large enough for the hose clamp on the back piece of plywood. Insert hose clamp and remove bottle. Here is what the back of my bird feeder looks like with the hose clamp:
Once all pieces have been cut and you have dry fitted them, it is time to start assembling the bird feeder. I chose to use both wood glue and brad nails to ensure that it would hold it’s shape even with warping from the weather. I added a small amount of glue in the channel of each piece and then added a brad or two. I would highly suggest using wood glue for longevity of the bird feeder. Do not glue the roof onto the feeder. Simply attach the two roof pieces together and they should be able to snugly fit with the channel. You need for the roof to be removable in order to refill the bird
Fill the wine bottle with bird seed and set in clamp. Tighten if needed and set roof on. You can hang the bird feeder directly onto a fence post or add a rope or ribbon and attach it to a tree limb.
Loving the look of this bird feeder, and the fact that it only took me a short time to create and build is a major plus. I think the neighborhood birds will appreciate it as well.